Lighting Installation in Edmonton

Work we handle for Edmonton properties:

• Recessed pot lights in kitchens, hallways, and finished basements, including recessed lighting installation in ceilings with no existing box
• LED lighting upgrades in Edmonton and retrofits of old fluorescent kitchen troffers
• Under-cabinet strips, pendants over islands, and vanity fixtures
• Dimmers, timers, motion sensors, and smart lighting controls
• Exterior soffit lighting, deck and step lights, and garden and pathway fixtures
• Garage, shed, and garden suite lighting on dedicated circuits

Yes, as this is common for two-storey homes and condos. Without an attic above, we use a shallow recessed housing rated for insulated ceilings and fish the wire down from the floor above or sideways through the joist bay. The cut-in opening is small, and most ceilings take the new box without needing a patch bigger than a standard ceiling medallion. If the joists run the wrong direction, we plan the layout around them rather than force a straight line. Either way, you get the finished look without tearing out drywall across half the room.

Swapping out a single fixture on existing wiring takes under an hour. Installing four pot lights in a finished basement—with a new circuit, permit, and vapor barrier boxes—usually takes four to six hours on site. Larger jobs, like a full kitchen relight with dimmers and under-cabinet LED strips, generally take a full day. It depends on how the wiring runs and whether we need to cut open drywall or fish wires blind.

We always give you a clear time estimate with your quote so you're not left guessing. If the project requires a City of Edmonton safety inspection, we book that separately once the work is closed in, based on city inspector availability. Typically, electrical permits for renovations include two inspections: a rough-in inspection before the work is concealed with drywall, and a final inspection once the drywall is reinstalled. Lighting projects could have either one or two inspections, depending on the nature of the work.

Fixtures mounted outside have to carry a wet-location or damp-location rating, and the right rating depends on where exactly the light sits. Soffit lights under an overhang that never see direct rain are damp-location rated. Fixtures out in the open, like post lights or wall sconces exposed to snow and freezing rain, need a wet-location rating. Edmonton winters push hardware hard. Freeze-thaw cycles crack cheap gaskets, and water inside a junction box above a garage door is a problem by spring. We check the rating on every fixture before it goes up. If you've picked something out already, bring the spec sheet and we'll confirm it before you buy a second one.

Cold air actually helps LED drivers run cooler during the winter months, and that extends driver life indoors. The problem shows up in unheated spaces: attached garages, cold storage rooms, or crawlspaces where temperatures drop well below zero. Standard LED fixtures aren't rated for those conditions, and drivers fail faster when they cycle from -25°C up to operating temperature every time the light switches on. We use cold-rated fixtures in unheated spaces and confirm the minimum starting temperature on the spec sheet before the install. For outdoor Edmonton fixtures, a cold-rated LED is worth the small price difference over a standard one.

Code allows a circuit to carry 80 percent of its rating on a continuous basis. On a standard 15-amp lighting circuit, that works out to 12 amps, or roughly 1,440 watts. A breaker might hold at 1,800 watts without tripping, but loading it there regularly runs the wiring hot. LED changes the math in your favour. Twelve 9-watt pot lights draw about 108 watts, so the practical limit is usually the box fill and the switch, not the breaker.

Usually not. Old rotary and slide dimmers were built for incandescent loads of 300 watts or more, and an LED array drawing 40 watts leaves them flickering, buzzing, or dead below half travel. You need a dimmer rated for LED with a compatible minimum load. Check the fixture spec sheet for the driver type before buying anything. We match the dimmer to the driver during the install, which kills the flicker most people blame on the bulbs.

Lighting is one piece of what our electricians do around the house. Common jobs include panel upgrades or an energy management system when a 100-amp service is already full, aluminum wiring repairs in homes built through the late 1960s and 1970s, EV charger installation, added outlets and dedicated circuits, and smoke and carbon monoxide alarm replacement. We also install surge protection at the panel, which shields integrated LED fixtures. Their drivers sit on the circuit permanently and take the hit when a surge comes through the line.

Pick a time online and tell us what you're planning. Pot lights in a basement, a kitchen relight, exterior fixtures before the snow: the detail helps us load the right parts. Book your Edmonton lighting appointment and one of our licensed electricians will walk the space, check the circuit, and quote the job in writing. We cover Edmonton, Sherwood Park, Beaumont, and Leduc.