The short answer: Tampa Bay cold snaps put winter loads on panels built for summer. Heat strips, space heaters, and pool heaters can push an older 100-amp panel to its limit, cool nights send roof rats looking for warm enclosures, and winter power outages stress aging breakers when power returns. Winter is also the best time to upgrade: scheduling is easier, and the work is done before summer. A 200-amp panel upgrade typically runs $3,500–$5,000 in Tampa Bay.
Tampa Bay homeowners spend October through March enjoying the weather and thinking ahead to hurricane season. Few think about what a 40-degree January night is doing to the electrical panel in the garage.
Florida winters are mild, but they are not easy on electrical systems. A cold front can send an entire neighborhood to its heat strips and space heaters within hours. An aging panel that handles summer air conditioning without complaint can struggle when those winter loads stack on top of everything else. Add rodents and other pests looking for warmth, and winter is when many panel problems first show up.
The good news: winter is also the best window of the year to fix them. Mr. Electric of Tampa Bay (License EC13015799) has served Hillsborough and Pinellas homeowners since 1994. This guide covers the four winter risks we see most, what they look like in your neighborhood, and how to get ahead of them. For general panel information, see our; Electrical Panel Repair & Upgrade guide.
Book Your Safety Inspection | (813) 474-9789
Risk 1: Cold Snaps Add Heavy Heating Loads to Your Panel
Why cold snaps matter: Most Tampa Bay homes heat with a heat pump backed up by electric resistance heat strips. A 10 kW heat strip draws roughly 40 amps at 240 volts. Add two 1,500-watt space heaters and a pool heater, and a home that is comfortable on a 100-amp panel in October may not be in January.
Tampa Bay does not get blizzards, but it does get cold snaps: two- to five-day stretches in December, January, and February when overnight lows fall into the 30s and 40s. Florida utilities see sharp early-morning demand peaks during these events, because so much of the state heats with electricity. TECO serves most of Hillsborough County, and Duke Energy Florida serves St. Petersburg and much of Pinellas.
What winter loads add up to
|
Winter load |
Typical draw |
What it means for your panel |
|---|---|---|
|
Heat pump in emergency or auxiliary heat (heat strips) |
5 kW strip about 21 A; 10 kW strip about 42 A at 240V |
One of the largest single loads in the home, running for hours at a time |
|
Portable space heater (1,500 W) |
About 12.5 A at 120V each |
Can overload a bedroom circuit shared with other plug loads |
|
Pool or spa heat pump |
Often on a dedicated 240V circuit sized for a large load |
Runs hardest on the coldest nights |
|
Electric water heater |
About 18–19 A at 240V (4,500 W) |
Higher demand as incoming water temperature drops |
Typical figures for reference. Actual draw depends on equipment nameplates. A load calculation under NEC Article 220 is the only reliable way to size your service.
What grid stress and power outages look like at your panel
-
Voltage sags: When demand spikes, voltage can dip briefly. Motors in compressors, pumps, and refrigerators draw more current to keep running, which adds heat to wiring and breakers.
-
Surges when power returns after an outage: When a power outage ends, the return can stress electronics and breaker mechanisms. Whole-home surge protection under NEC 230.67 is designed for exactly this.
-
Breakers near their limits: Breakers are sized so continuous loads stay at or below 80% of their rating. Hours of heat-strip and space-heater use on a winter night is a continuous load.
Power Outage in Tampa Bay? Is It the Utility or Your Panel?
Quick check: If your neighbors are also dark, it is a utility power outage. Report it to TECO (Hillsborough) or Duke Energy Florida (Pinellas) and wait for restoration. If only your home, or only part of your home, lost power, the problem is likely on your side: the main breaker, the panel, the meter base, or the service connection. That needs a licensed electrician.
-
Whole neighborhood out: a utility power outage. Check the TECO or Duke Energy Florida outage map and report it. Do not open the panel.
-
Only your home out: check whether the main breaker has tripped. If the breaker continuously trips or will not reset, call an electrician.
-
Half the house out, or lights dim and brighten: a partial power outage often means a lost leg of your 240-volt service, a failing main breaker, or a loose service connection. Turn off large loads and call for same-day service.
-
Burning smell, buzzing, or a hot panel after an outage: call an emergency electrician now.
After any power outage: before power returns, turn off heat strips and unplug sensitive electronics so they do not all start at once. When power is restored, bring loads back gradually. A breaker that trips repeatedly after a power outage is telling you something. Do not keep resetting it.
Risk 2: Roof Rats Look for Warm Places, and Your Panel Is One
Why rodents matter: Roof rats (often called palm rats in Florida) stay active year-round and look for warm, enclosed spaces on cool nights. Open knockouts, gaps around conduit, and corroded service-entrance seals let them into panels and attics, where chewed insulation and nesting material can cause shorts, arcing, and overheating.
Roof rats, known locally as palm rats, are excellent climbers. They travel along tree limbs, utility lines, and conduit to reach rooflines, soffits, and exterior panels. South Tampa's live-oak canopy and the palms throughout Pinellas County give them easy routes to older homes. Squirrels cause similar damage in attics.
What rodent damage looks like
|
Damage |
Electrical consequence |
How it is found |
|---|---|---|
|
Chewed insulation on wiring in attics, walls, or the panel |
Short circuits, arc faults, fire risk |
Often hidden; found during an inspection |
|
Nesting material packed around breakers |
Overheating and breaker malfunction |
Visible when the panel cover is removed |
|
Droppings and urine on breakers and terminals |
Corrosion and higher resistance at connections |
Visible on inspection |
Warning signs
-
Breakers tripping on circuits with no unusual load
-
A burning or musty smell near the panel
-
Scratching in walls or the attic near the panel
-
Flickering lights on one circuit with no obvious cause
-
Gnaw marks on exterior conduit or gaps around the panel enclosure
Do not open the panel or pull out nesting material yourself. Debris inside an energized panel is a shock and arc-flash hazard. Call a licensed electrician to de-energize, clean, repair, and seal the enclosure, and coordinate with your pest control company to close the entry points so it does not happen again.
Risk 3: Repeated Winter Loads Wear Out Aging Panels
Why aging panels matter: Every time a breaker carries heavy current, its internal trip mechanism heats and cools. Over decades, that wear can make an old breaker trip late or not at all. Winter cold snaps add large, sustained loads on top of normal use, so a marginal panel gets pushed harder than at any other time of year.
A single cold snap does not ruin a panel. Twenty-five winters of cold snaps on a panel that was undersized from the start is a different story. Electrical distribution and lighting equipment is consistently among the leading causes of U.S. home fires, according to the National Fire Protection Association, and aging, overloaded panels are part of that picture.
Winter warning signs in your panel
|
Warning sign |
What it may indicate |
What to do |
|---|---|---|
|
Burning smell near the panel |
Active arcing or overheating insulation |
Call an electrician now |
|
Panel cover warm to the touch, buzzing, or humming |
Loose connections, arcing, overloaded bus |
Schedule same-day service |
|
Breaker trips and will not reset |
Internal breaker fault or a wiring fault |
Schedule same-day service |
|
Same breaker trips during cold snaps |
Overloaded circuit or worn breaker |
Inspect this week |
|
Lights dim when heat strips or the AC compressor start |
Service near capacity or a loose connection |
Book a safety inspection |
The 100-amp panel question
Many Tampa Bay homes built before 1990 still have 100-amp service. A modern household with central air, an electric dryer, an electric water heater, and today's appliances can approach that limit on a summer afternoon. Add a winter heat-strip cycle and two space heaters, and there is little margin left. A load calculation under NEC Article 220 tells you whether your service is actually undersized or just needs a few circuits rebalanced.
Some panels are a problem regardless of size. Federal Pacific Stab-Lok, Zinsco, and some Pushmatic panels are commonly flagged by Florida insurers and should be evaluated by a licensed electrician in any season.
What Winter Means for Your Tampa Bay Neighborhood
Winter panel risks look different depending on the home. Here is what our most common electrical findings across Hillsborough and Pinellas County.
Older homes: Hyde Park, Seminole Heights, Palma Ceia, Old Northeast and Kenwood
Bungalows and mid-century homes in these neighborhoods are where 100-amp service, original or insurer-flagged panels, and space heaters on old bedroom circuits meet. Mature oak canopies and older soffits give roof rats easy access to attics. Many Florida homeowners' policies renew in the first months of the year, and a 4-point electrical safety inspection that flags the panel can force a rushed replacement. Winter is the time to get ahead of that.
Waterfront homes: Davis Islands, Harbour Island, Snell Isle, and Shore Acres
Winter cold fronts bring strong north winds and salt spray, and exterior panels and meter bases on waterfront homes keep corroding year-round. Many homes that took storm surge from Hurricanes Helene and Milton in 2024 have panels and breakers that were dried out but never replaced, and saltwater corrosion continues after the water is gone. Corroded connections are also a common reason a waterfront home has a power outage when the rest of the street does not. The quieter winter months are the right time to replace corroded outdoor service equipment and check dock and boat-lift circuits before boating season picks up.
Pool and spa homes: Westchase, Tampa Palms, Carrollwood and Avila
Pool heat pumps and spa heaters work hardest on the coldest nights, often at the same time as the home's heat strips. Freeze-protection settings also run pumps overnight. If a breaker trips on cold mornings, the panel may be undersized for everything running at once. Winter is also a good time to check pool bonding and GFCI protection while the pool sees less use.
Modern homes: Keystone, New Tampa, and South Tampa
Newer homes usually have 150- or 200-amp service and handle winter loads well. The winter question is planning ahead: adding a Level 2 EV charger, battery backup such as the Anker Solix E10 to keep the lights on during a power outage, or a standby generator before summer and hurricane season. Most homes built before Florida's 8th Edition (2023) Building Code took effect on December 31, 2023 were not required to have whole-home surge protection, so that is worth adding too.
Seasonal and snowbird homes: Clearwater Beach, Belleair and Indian Rocks Beach
Homes that sat closed through summer and fall are prime targets for rodents and moisture. Before turning everything back on for the season, it is worth a quick check of the panel, exterior receptacles, and attic for nesting, corrosion, or chewed wiring. The same goes for holiday lighting: plugging large displays into exterior outlets that have not been used in months is how GFCIs fail. See our Holiday Lighting Design guide for safe outdoor power planning.
Why Winter Is the Best Time to Upgrade Your Panel
Why winter works: Spring and summer bring storm-prep demand and post-storm repair work. In winter, scheduling is more flexible, permits and utility coordination for the service disconnect and reconnect typically move more smoothly, and your new panel is in place well before summer heat and hurricane season.
Easier scheduling
Demand for licensed electricians in Tampa Bay climbs in late spring as homeowners prepare for hurricane season, and again after any storm. Winter gives you more choice on dates, and the work gets done before the next cold snap instead of during it.
Smoother utility and permit coordination
A panel or service upgrade requires a permit and coordination with TECO or Duke Energy Florida to disconnect and reconnect service. We handle both. Outside peak storm season, that coordination is generally easier to schedule around your plans.
Time before summer
A panel upgraded in December, January, or February is inspected and in service before the first heat wave. That leaves time to add whole-home surge protection, plan an EV charger, or size a generator or battery system before storm season. Think of it like replacing your tires in the fall: you do it before you need it.
What a 200-Amp Panel Upgrade Includes in Tampa Bay
-
Load calculation under NEC Article 220 to confirm the right service size.
-
New 200-amp main breaker panel using listed equipment from established manufacturers.
-
Permit and inspection through the City of Tampa, Hillsborough County, Pinellas County, or your municipality.
-
Utility coordination with TECO or Duke Energy Florida for the disconnect and reconnect.
-
Whole-home surge protection, required under NEC 230.67 when service equipment is replaced.
-
Grounding and bonding brought to current code.
Most standard upgrades are completed in a single day. Homes that need service entrance work, a meter relocation, or circuit repairs may take longer, and we identify that during the evaluation. A standard 200-amp upgrade typically runs $3,500–$5,000. Monthly payment options are available through GreenSky.
Illustrative range, not a quote. Pricing is confirmed in writing after an on-site evaluation.
The insurance angle
Florida insurers often require a 4-point inspection on older homes, and the electrical section looks closely at the panel. Insurer-flagged brands (Federal Pacific, Zinsco, some Pushmatic), double-tapped breakers, and visible corrosion are common reasons for a required repair or non-renewal. A permitted panel replacement with a passed county inspection gives your 4-point inspector and underwriter clear documentation.
Your Winter Electrical Checklist
Late Fall (November/December)
-
Look at the outside of your panel. Rust, gnaw marks, or gaps around conduit are worth a call.
-
Check the panel label. Federal Pacific, Zinsco, or Pushmatic panels should be evaluated by a licensed electrician.
-
Find your main breaker size. If it says 100 and your home has central air and an electric dryer, a load calculation is overdue.
-
Know who to call in a power outage: TECO in Hillsborough County, Duke Energy Florida in Pinellas, and a licensed emergency electrician if only your home is affected.
-
Plug space heaters directly into wall outlets, never into power strips or extension cords, and keep them on circuits that are not already heavily loaded.
Before the next cold snap
-
Schedule an electrical safety inspection. A licensed electrician will open the panel, check breaker condition, look for rodent evidence, and compare your service size to your actual load. Inspections typically run $500–$1,000.
-
If an upgrade is recommended, schedule it in winter while dates are flexible.
-
If you are a Mr. Electric Advantage Plan member, your annual safety inspection is included. Winter is a good time to use it.
After any panel work
-
Confirm that whole-home surge protection was installed.
-
Keep at least 36 inches of clear working space in front of the panel (NEC 110.26). Garage storage stacked against the panel wall is a common violation.
Frequently Asked Questions
Why does my breaker trip when it gets cold in Tampa?
Cold snaps add heavy heating loads: heat strips, space heaters, and pool or spa heaters running at the same time as everything else. A breaker that trips only on cold nights usually means an overloaded circuit, a worn breaker, or a service that is undersized for your winter load. A licensed electrician can tell which.
How much does a panel upgrade cost in Tampa?
A standard 200-amp panel upgrade in Tampa Bay typically costs $3,500–$5,000, including the permit and inspection. Service entrance work or circuit repairs can add to that. Mr. Electric of Tampa Bay provides an upfront written price before work begins.
Is winter a good time to replace an electrical panel in Florida?
Yes. Scheduling is generally more flexible than in spring and summer, and the new panel is in service before summer heat and hurricane season, with time to add surge protection or plan backup power.
What should I do after a power outage in Tampa?
If the whole neighborhood is out, report the power outage to TECO or Duke Energy Florida. If only your home or part of it is out, check the main breaker once, then call a licensed electrician if it trips again. Unplug electronics and turn off heat strips during the outage, and bring loads back gradually when power is restored.
Why do my breakers trip when power comes back after an outage?
When power returns, heat strips, AC compressors, refrigerators, and pool equipment can all start at once, creating a large inrush of current. A healthy panel usually handles it. Breakers that trip every time after a power outage point to an overloaded circuit, a worn breaker, or an undersized service.
Can rats get into an electrical panel?
Yes. Roof rats (palm rats) can enter through open knockouts, gaps around conduit, and corroded seals, and they chew insulation and leave nesting material and droppings that cause shorts and corrosion. Do not clean it out yourself: have a licensed electrician de-energize, repair, and seal the panel.
Is it safe to use space heaters in an older Tampa home?
Use them carefully. Plug each heater directly into a wall outlet, never into a power strip or extension cord, and avoid running more than one on the same circuit. If breakers trip or outlets feel warm, stop using the heater on that circuit and have the wiring checked.
Will a new panel help with my homeowners insurance?
Often, yes. Insurer-flagged panels and visible corrosion are common 4-point inspection findings. A permitted replacement with a passed county inspection gives your insurer clear documentation of the upgrade.
