How do I know if my panel needs repair instead of a full replacement?

A repair fixes one bad breaker or a loose connection without touching the rest of the box. Replacement makes sense when the panel itself is the problem: a recalled Federal Pacific or Zinsco brand, corroded bus bars, or a main breaker rated below what your home now draws. We test the load first. Roughly half the panel calls we run in Mission end as a targeted repair, not a swap.

What's the difference between panel repair and a panel upgrade?

Repair replaces a failed part inside the existing box. An electrical panel upgrade replaces the panel itself with a higher amperage unit, usually 150 or 200 amps, plus new breakers rated for today's code. Homeowners adding an EV charger or a second HVAC unit usually need the upgrade, since the existing bus bar has no room left for another breaker.

Why do older Mission homes need panel work more often than newer builds?

Mission's housing stock ranges from 1920s bungalows and Tudor cottages near Johnson Drive to 1950s ranches and split-levels farther out, and almost none of that stock was wired for what modern kitchens and garages now demand. A 1948 bungalow built with a 60-amp fuse box was never meant to run a dishwasher, a microwave, a window AC, and a chest freezer on one circuit. We see breaker trips cluster in exactly those homes every summer once the window units come out of storage.

What other services does Mr. Electric offer in Mission?

Beyond panel repair, we handle circuit breaker replacement , home generator installation for whole-house backup, ceiling fan installation , and EV charger installation for Level 2 home charging. Most of these get bundled with a panel visit when the existing box doesn't have room for a new dedicated circuit. If your dryer or shop tools keep tripping a shared breaker, a dedicated circuit paired with the panel work usually solves it in one trip.

Is a permit required for electrical panel repair in Mission, KS?

Yes, for most panel work beyond swapping a single breaker. The City of Mission Building Inspector issues the permit and inspects the finished work against the 2017 National Electrical Code with local amendments. Our electricians hold current Johnson County Contractor Licenses, so the paperwork and inspection scheduling are handled without you having to track down a separate contractor number.

What happens during a typical panel repair visit?

Most breaker or lug repairs are completed in a single visit, usually two to four hours, depending on what the load test finds. A full panel replacement runs longer, often a full day plus a follow-up inspection once the City schedules it. We'll tell you which one you're looking at once the load calculation is done, before any teardown starts.

How do I schedule electrical panel repair in Mission, KS?

Call or book online, and we'll ask about the symptoms first: tripping breakers or a warm panel cover, then send an electrician out with the right parts already on the truck. The scheduling process works the same way for Mission and for our main office area around Overland Park. Schedule a panel repair appointment today , and we'll confirm a window that works before anyone shows up.

Electrical Panel Repair Mission, KS

Grounded Panels for Mission's Older Homes

If your breaker box trips every time the AC and the microwave run together, the panel is probably undersized for what your Mission home now asks of it. Our Mission electrician crew traces the fault and tests the load before touching a single breaker. Bungalows and ranches built here in the 1940s and 50s often have 60- or 100-amp service that can't keep up with central air, an EV charger, a finished basement, or a hot tub.

Grounded Panels for Mission's Older Homes

Mr. Electric of Phoenix Metro electrician tools on a countertop in Phoenix, AZ.

Residential
Commercial

Book Online

First Name*

Last Name*

Email*

Phone Number*

Street Address**

ZIP/Postal Code*

Yes! You can text me service reminders and other messages.

By checking this box, I agree to opt in to receive automated informational and promotional SMS and/or MMS messages from Mr. Electric, a Neighborly company, and its franchisees to the provided mobile number(s). Messages & data rates may apply. Message frequency varies. View Terms and Privacy Policy. Reply STOP to opt out of future messages. Reply HELP for help.

By entering your email address, you agree to receive emails about services, updates or promotions, and you agree to the Terms and Privacy Policy. You may unsubscribe at any time.

Our Electrical Panel Repair Process for Mission Homes

We start with a load calculation, not a guess. A clamp meter reads amperage across each breaker while the panel runs its normal daytime demand, and if there's any doubt about the main breaker, we pull the panel cover and inspect the lugs directly. Homes we service from Mission to our Overland Park electrician office share the same core problem: original panels from the Truman and Eisenhower years weren't sized for central air, an electric range, a water heater, and a Level 2 EV charger running at once.

Every panel gets opened at the breakers for a hands-on check. We look for double-lugged neutrals, corroded bus bars, and Federal Pacific or Zinsco panels, both known for breakers that fail to trip when they should. Repair and replacement work is permitted through the City of Mission Building Inspector and is subject to the National Electrical Code with the city's local amendments.

If an overloaded circuit or a faulty main breaker caused the failure, we size the new panel for what you actually run day-to-day: central air, a range, a backup water heater, and whatever's charging in the garage. Wiring upgrades happen at the same visit when knob-and-tube or aluminum branch circuits feed into the panel.

Why Mission Homeowners Choose Mr. Electric for Electrical Panel Repair

Mr. Electric of Overland Park has worked Johnson County panels since 1996, and our field crew of 8 licensed electricians averages 10 years in the trade. The electrician testing your breakers has likely opened a hundred boxes just like yours. We cover Mission alongside Merriam and Shawnee, two of the closest service areas, with the same mid-century wiring, aluminum branch circuits, and undersized service on panels that predate GFCI requirements.

If a repair uncovers a recalled panel brand or old knob-and-tube wiring, we walk you through the code-compliant fix before any breaker gets touched, not after. That includes electrical code updates tied to AFCI breaker requirements and full service-entrance replacements where the mast or meter base has corroded beyond repair. Ready to get the panel checked out? Contact us today, and we'll schedule an electrician.

9393 W 110th Street Suite 500, Office 555 Overland Park, KS 66210, USA

Antioch
Baldwin City
Basehor
Bonner Springs
De Soto
Edgerton
Edwardsville
Eudora
Gardner
Kansas City
Lansing
Leavenworth
Leawood
Lenexa
Linwood
Merriam
Mission
New Century
Olathe
Overland Park
Prairie Village
Shawnee
Spring Hill
Stilwell
Tonganoxie

Service We Provide

Residential
Commercial

Frequently Asked Questions About Electrical Panel Repair: Mission, KS

A repair fixes one bad breaker or a loose connection without touching the rest of the box. Replacement makes sense when the panel itself is the problem: a recalled Federal Pacific or Zinsco brand, corroded bus bars, or a main breaker rated below what your home now draws. We test the load first. Roughly half the panel calls we run in Mission end as a targeted repair, not a swap.
Repair replaces a failed part inside the existing box. An electrical panel upgrade replaces the panel itself with a higher amperage unit, usually 150 or 200 amps, plus new breakers rated for today's code. Homeowners adding an EV charger or a second HVAC unit usually need the upgrade, since the existing bus bar has no room left for another breaker.
Mission's housing stock ranges from 1920s bungalows and Tudor cottages near Johnson Drive to 1950s ranches and split-levels farther out, and almost none of that stock was wired for what modern kitchens and garages now demand. A 1948 bungalow built with a 60-amp fuse box was never meant to run a dishwasher, a microwave, a window AC, and a chest freezer on one circuit. We see breaker trips cluster in exactly those homes every summer once the window units come out of storage.
Beyond panel repair, we handle circuit breaker replacement, home generator installation for whole-house backup, ceiling fan installation, and EV charger installation for Level 2 home charging. Most of these get bundled with a panel visit when the existing box doesn't have room for a new dedicated circuit. If your dryer or shop tools keep tripping a shared breaker, a dedicated circuit paired with the panel work usually solves it in one trip.
Yes, for most panel work beyond swapping a single breaker. The City of Mission Building Inspector issues the permit and inspects the finished work against the 2017 National Electrical Code with local amendments. Our electricians hold current Johnson County Contractor Licenses, so the paperwork and inspection scheduling are handled without you having to track down a separate contractor number.
Most breaker or lug repairs are completed in a single visit, usually two to four hours, depending on what the load test finds. A full panel replacement runs longer, often a full day plus a follow-up inspection once the City schedules it. We'll tell you which one you're looking at once the load calculation is done, before any teardown starts.
Call or book online, and we'll ask about the symptoms first: tripping breakers or a warm panel cover, then send an electrician out with the right parts already on the truck. The scheduling process works the same way for Mission and for our main office area around Overland Park. Schedule a panel repair appointment today, and we'll confirm a window that works before anyone shows up.